Corey T Posted April 21, 2020 Posted April 21, 2020 I’m supposed to feed my line OVER the stabilizer bar on my Tat SV TW... right?? 1 1 3
Corey T Posted April 21, 2020 Author Posted April 21, 2020 1 minute ago, Born 2 fish said: No it goes under. Thank you!
Born 2 fish Posted April 21, 2020 Posted April 21, 2020 Just now, Midwest Big Bass said: Thank you! ?
garroyo130 Posted April 21, 2020 Posted April 21, 2020 Looks like it goes over (1:52) screenshot attached
Super User MassYak85 Posted April 21, 2020 Super User Posted April 21, 2020 It absolutely goes over. 1
Corey T Posted April 21, 2020 Author Posted April 21, 2020 Haha I put myself out there with an embarrassing question and now I feel like I am getting messed with and don’t know what to think! ??♂️? 1
garroyo130 Posted April 21, 2020 Posted April 21, 2020 1 minute ago, Midwest Big Bass said: Haha I put myself out there with an embarrassing question and now I feel like I am getting messed with and don’t know what to think! ??♂️? What i posted is an official Daiwa USA video. It confirms it goes over. 2
Corey T Posted April 22, 2020 Author Posted April 22, 2020 41 minutes ago, garroyo130 said: What i posted is an official Daiwa USA video. It confirms it goes over. Im going with this quality PI work here. Thanks garroyo130. 1
rangerjockey Posted April 22, 2020 Posted April 22, 2020 Under, The line should be in the slot of the T wing not rubbing the top of it. The line comes off the spool and directly through the T wing not rubbing back and forth across that pin. 1
Fishingmickey Posted April 22, 2020 Posted April 22, 2020 13 hours ago, garroyo130 said: What i posted is an official Daiwa USA video. It confirms it goes over. It may be the "official" advertising video. But the question remains did they get it right. I'd ask the question does the line rub against the T-wing or the bar when it is fed over? If it does rub, I'd go under for the win. FM
Corey T Posted April 22, 2020 Author Posted April 22, 2020 Shoot you guys are killing me here. Why is this so hard?! Lol so I’ve tried it both ways. I will say that casting is much easier when I feed it over. With that said, I don’t want to be fraying line or damaging components in any way.
Super User DitchPanda Posted April 22, 2020 Super User Posted April 22, 2020 Your supposed to drill a tiny hole and go through it. Just kidding man don't do that. I'm not sure which way it's supposed to go...just wanted to add to the confusion! I would call or email them for clarification if it was me. 1 3
evo2s197 Posted April 22, 2020 Posted April 22, 2020 It goes over not under, otherwise what's the purpose of the T wing..... 2
Super User MassYak85 Posted April 22, 2020 Super User Posted April 22, 2020 44 minutes ago, Midwest Big Bass said: Shoot you guys are killing me here. Why is this so hard?! Lol so I’ve tried it both ways. I will say that casting is much easier when I feed it over. With that said, I don’t want to be fraying line or damaging components in any way. I'm shocked how split this is from the responses. Like you said, you will cast much better with it over and it will be noticeable when you do it under that it's getting some resistance. Going under I would think would pin the line into the smaller groove of the T wing even when casting, which is not the intent of the design. The intent is it goes through the wider section when the thumb bar is pressed when casting, and through the thinner section when reeling in. I've got 3 T wing reels and I've gone over the bar for all of them. None of them rub, I use braid for all of them, and there is no grooving on my Twings. 1
rangerjockey Posted April 22, 2020 Posted April 22, 2020 Looks like 2 different reels. The one in the pic the poster has looks like the pin is above the T wing. In the pic Evo put up it looks like its below. There has been several different models of Tatulas, Maybe the pin is different ? There is a difference between that pin and the pawl the Twing is mounted to. 1
Corey T Posted April 22, 2020 Author Posted April 22, 2020 So I went back and compared to my Steez CT SV and Zillion SV for comparison. The stabilizer bar is MUCH lower in both of those reels. So much so that there is no way that feeding under could be right. I’m 99% sure it is supposed to be fed over at this point. @evo2s197 also added a picture that pretty much confirms it. Crazy! 1
evo2s197 Posted April 22, 2020 Posted April 22, 2020 17 minutes ago, rangerjockey said: Looks like 2 different reels. The one in the pic the poster has looks like the pin is above the T wing. In the pic Evo put up it looks like its below. There has been several different models of Tatulas, Maybe the pin is different ? There is a difference between that pin and the pawl the Twing is mounted to. It goes over it doesn't matter what iteration it is. 1
rangerjockey Posted April 22, 2020 Posted April 22, 2020 It goes under Look at the pic at the upper right.. whatever hammer 1 1
Corey T Posted April 22, 2020 Author Posted April 22, 2020 45 minutes ago, MassYak85 said: I'm shocked how split this is from the responses. Like you said, you will cast much better with it over and it will be noticeable when you do it under that it's getting some resistance. Going under I would think would pin the line into the smaller groove of the T wing even when casting, which is not the intent of the design. The intent is it goes through the wider section when the thumb bar is pressed when casting, and through the thinner section when reeling in. I've got 3 T wing reels and I've gone over the bar for all of them. None of them rub, I use braid for all of them, and there is no grooving on my Twings. I agree with this. I have the Steez CT SV, Zillion SV and 2020 Tatula SV all fed over right now and will say that all three do push the line against the top part of the TWS when in casting position. With that said, I wouldn’t say there is much tension or friction at that point of contact.
evo2s197 Posted April 22, 2020 Posted April 22, 2020 7 minutes ago, rangerjockey said: It goes under Look at the pic at the upper right.. 1
Recommended Posts