Jump to content

Recommended Posts

Posted

I bought this lil 10 TinCup fer $100, she had some minor leakage around a few rivits and seams, and the back was so worn from being pulled around over the years you could almost poke a finger thru-it.

I stripped the entire bottom of the boat using a wire brush and a drill, took bout an hour, not bad considering I brought it to bare metal.

untitled-1.jpg

untitled3.jpg

On the inside I filled the holes with JB Weld and ran a bead like filler up about 6 to 8 inches from the back...

drainplug.jpg

jbweld.jpg

I used self etching primer and a lil dab of Krylons ODG flat.

Posted

next I tackled the bottom. What I used was Fasco's 9X SteelFlex 2 part epoxy and mixed in the OD Green color. Surface prep is key with this stuff and bringing the bottom to bare metal is a MUST, the rougher the surface the better the epoxy will adhere to it...It comes in quart kits and each kit will cover approximetly 30 sq ft providing how thick it's applied...I ordered 2 quarts and color and it ran me a lil over $50 shipped from FLA...I mixed 1 quart kit at a time and used foam brushes and rollers.....it came out really good considering I ran into some trouble on my second coat and was ready to throw in the towel, but all is well and the epoxy did exactlty what it claimed to do. Protect the bottom from light scratches and place a water tite seal around the boat...NO MORE LEAKY RIVITS...EVER

9x.jpg

What looks really good is I painted my boat with Krylons ODG Flat paint and where the epoxy & paint meet, the colors blended well

sears.jpg

Posted

after the epoxy dried I then prepped the boat surface for painting, I lightly sanded it, washed it down and rubbed the surface with acetone, as the same went for the bottom....I used Self Etching Primer and Krylons ODG Flat. I dont have many pix of the paint but I can provide a custom paint I did on the side...

loomy.jpg

sorry the camera isnt the best...its my cell phone

Posted

I then went to work on the interior....knowing she's only 10ft I really cant deck her so I just made my footing a little more stable and added a small 4" deck in the front with storage, and tried to muffle the sounds of a tin cup in open water...I used the artifical turf from the De-Pot, it was reasonably priced and it suited my needs and my buget. I had some plywood & 2x4s lyin around so I put em to good use.

turfshot.jpg

inprogress.jpg

this was my goal for up front, to level the footing area and make a solid platform for my daughter to stand on and provide storage when Im out alone.

frntdck.jpg

frntdcklatch.jpg

storage-1.jpg

the platform to left of the storage locker is also removable to provide extra storage if need be.

Posted

They bottom looks like it came out great, better then new.  I wish I could flip my boat over and work on the bottom of the boat.

Posted

Great Job!

I think you will really enjoy getting out on the water now.

Posted

Awesome job,

I wish I had your luck an could find a steal like that.

I am sure you and  your daughter will have a blast with it.

memo

  • Super User
Posted

GREAT WORK! Just a heads up, if you put swivel seats on it, the Astro Turf is just going to come off the seats. We gave up and  the swivels onto wood then put wood over the metal and then painted it green and put  on the seats, worked a whole lot better!

Posted

Looks good, I wish my first jon boat would have looked like that.

Where did you get the hardware for the storage compartment?

I already have the hinges, im just looking for the thing you pull on to open the compartment (not sure of the name).

thanks

nick

Posted

Thanks for all the compliments guys, Muddy, the seats I have are nor going to be permenatly mounted but the jb clamp style, not sure if that'll be a problem but will keep an eye on it, thank you.

rondef, hopefully this week, I have a couple loose ends to tidy up but should be good2go, if it ever stops raining here in the NorthEast...lol

Kansas Angler, I bought my latches & lift ring from the local boating supply store, BoatersWorld, we have a West Marine too.

Thanks Again guys...I'll snap a couple more when she's 100% done, if that ever happens ;)

  • 3 weeks later...
Posted
next I tackled the bottom. What I used was Fasco's 9X SteelFlex 2 part epoxy and mixed in the OD Green color. Surface prep is key with this stuff and bringing the bottom to bare metal is a MUST, the rougher the surface the better the epoxy will adhere to it...It comes in quart kits and each kit will cover approximetly 30 sq ft providing how thick it's applied...I ordered 2 quarts and color and it ran me a lil over $50 shipped from FLA...I mixed 1 quart kit at a time and used foam brushes and rollers.....it came out really good considering I ran into some trouble on my second coat and was ready to throw in the towel, but all is well and the epoxy did exactlty what it claimed to do. Protect the bottom from light scratches and place a water tite seal around the boat...NO MORE LEAKY RIVITS...EVER

9x.jpg

What looks really good is I painted my boat with Krylons ODG Flat paint and where the epoxy & paint meet, the colors blended well

sears.jpg

AC how many coats did you get out of 2 quarts?  Do you think I'll have enought to do the whole out side of my boat

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Unfortunately, your content contains terms that we do not allow. Please edit your content to remove the highlighted words below.
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.


  • Outboard Engine

    Fishing lures

    fishing forum

    fishing forum

    fishing tackle

    fishing

    fishing

    fishing

    bass fish

    fish for bass



×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.