Jump to content

Recommended Posts

Posted

Earlier I mentioned that a buddy had this reel nib. Yesterday I finally picked it up and I'm not wowed by the reel.  It appears to be plastic and the rubberized surfaces are tacky.  This particular model was made in Sweden.

 

My question is this...it could certainly benefit from a good cleaning and oiling.  It's been in a plastic sealed box for years and is most likely gummed.  Should I drop the cash on having it tuned and cleaned?

 

The last issue is I've read that most reel guys are reluctant to work on these reels because of the planatery gearing system.  If you believe it's worth salvaging, do you know of anyone that works on em? 

 

Thanks for any input.  

 

-J

14857068287121727594225.jpg

Posted

Is it that bad?  30 views and no comments...Lmao!! 

 

-J

  • Super User
Posted
2 hours ago, XF15-Loader said:

Is it that bad?  30 views and no comments...Lmao!! 

 

-J

 

Most of the people on the board have never heard of that reel. The FEW that might know about that reel and can share some experience might not have come by yet. THEN, there might be a few people that DO know about that reel but want nothing more to do with it and are hiding...;)

 

Me, I own 20 Ambassadeur round reels and I know nothing about the Eons...
 

  • Like 2
Posted
6 minutes ago, Goose52 said:

 

Most of the people on the board have never heard of that reel. The FEW that might know about that reel and can share some experience might not have come by yet. THEN, there might be a few people that DO know about that reel but want nothing more to do with it and are hiding...;)

 

Me, I own 20 Ambassadeur round reels and I know nothing about the Eons...
 

That's what I'm afraid of, @Goose52...Lol.  

Posted

I had one of those lol. One of the worst reels I ever had. As far as the rubber getting sticky on the reel, mine did the same thing in its original box. Almost like it was melting. The brakes were extremely temperamental, some times it was like there was no braking and it would cast a mile, then the next cast would go nowhere. I could hold the reel and twist the whole gear side plate and handle. It was supposed to have a disengaging level wind. Sometimes it did, sometimes it didn't. The planetary gears were actually a pretty simple design, but it was a nightmare opening up the reel to get to them. After I decided I was never going to use it again, I wanted to see the inside of it lol.

 

I traded it in at BPS during the spring classic trade in. It may end up being a great reel for you, but I personally wouldn't invest much money in it. 

Posted

Thanks for the insight, @Boogey Man.  I've got plenty of decent reels so this may have to play third string...Lol.  

Posted

I will say that there were some people that loved the EON series.  Check out the bass fishing homepage that used to be at another site.org.  There used to be a lot of info on there when people did post often.  If that doesn't work just google bass fishing home page rods/reels.  I never used one but why not try it out and see if you have good luck with it.

Posted

I had and fished an eon 5600 back in 2000 & 2001, I fished for stripers and hybrids below the dam on Toledo with that reel and other abu(5500/6500). I remember the reel having the longest freespool of any reel I have ever seen. It also cast great too, but with that said I was also using 1oz buck tails and spoons. So I can't say how well it would do with lighter stuff. Stood up to numerous 8-12 stripes though. 

Posted

have all abu's, never had an eon never wanted one.there are collectors that want them for some unknown reason.

  • Like 1
Posted

I have over 80 Ambassadeurs,but that reel will never make it in my collection lol! Stick with the Classics,you'll never go wrong. There's a reason AbuGarcia discontinued those reels they sucked!

20160625_193951.jpg

  • Like 3
  • Super User
Posted

I had one. It was a great casting reel until I took it apart. I had a guide on Lake of the Ozarks tell me he had never seen anybody throw a DD22 that far.

 

The side plate was soft, and had to be pried off. It was never the same after that.

If the one you have works, use it. Don't try to service it. Use it until it pukes. 

 

  • Like 1
  • 4 years later...
Posted

Had the opportunity on one of these.  For $29 I figured whatever.  It casts really well but tends to backlash if you really zing it and I don't think there is a cast control knob on it to control the cast.  The one I have is just the Eon 3600, not the Pro or SE.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Unfortunately, your content contains terms that we do not allow. Please edit your content to remove the highlighted words below.
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.


  • Outboard Engine

    fishing forum

    fishing tackle

    fishing

    fishing

    fishing

    bass fish

    fish for bass



×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.