Loop_Dad Posted July 22, 2014 Posted July 22, 2014 The rod tip of my Crucial (6'8" MHF) got broken. I tried to buy replacement kits from eBay which didn't go well. I wasted too much time already. Now I'll just going to order correct one from jannsnetcraft to be done with. However I am not sure which one is the right one. How do you figure out the right tube size, ring size and type of the tip? They have lots of choices here: http://www.jannsnetcraft.com/fuji-tip-tops/ Quote
shanksmare Posted July 22, 2014 Posted July 22, 2014 I would take the rod to a tackle shop in your area that builds custom rods. They will be able to fit the proper sized tip top to the rod blank. It may cost you a few pennies more but you will save you the aggravation of getting the wrong size tip top. They will also have the rod cement you will need. Most will probably install it for you for free. 1 Quote
Delaware Valley Tackle Posted July 22, 2014 Posted July 22, 2014 Unless it's a micro guide rod, the tip ring size is likely 6. The tube size is in 64ths of an inch (size 5 tube = 5/64). Put a pair of calipers on the blank 1/4" back from the tip and convert the measurement to 64ths. http://www.guidesnblanks.com/chart/2 The last part is to match the finish. Attach with a high temp hot glue. Quote
Super User Darren. Posted July 22, 2014 Super User Posted July 22, 2014 I would take the rod to a tackle shop in your area that builds custom rods. They will be able to fit the proper sized tip top to the rod blank. It may cost you a few pennies more but you will save you the aggravation of getting the wrong size tip top. They will also have the rod cement you will need. Most will probably install it for you for free. This is what I do, although there is usually a fee associated with the service. Quote
shanksmare Posted July 22, 2014 Posted July 22, 2014 This is what I do, although there is usually a fee associated with the service. I guess it depends on the shop and how often you frequent it. If they have the tip top you need, you can do it yourself. It is simple to do. You can use meltable rod glue, archery broadhead glue or even 5 minute epoxy. If you use the epoxy make sure it is the 5 minute type. Then it can be removed with gentle heat if need be. Quote
Super User Darren. Posted July 22, 2014 Super User Posted July 22, 2014 I guess it depends on the shop and how often you frequent it. If they have the tip top you need, you can do it yourself. It is simple to do. You can use meltable rod glue, archery broadhead glue or even 5 minute epoxy. If you use the epoxy make sure it is the 5 minute type. Then it can be removed with gentle heat if need be. Oh I've done quite a few rod tips myself. Just prefer to have a pro do it now-a-days. He's always got the right tip sizes, etc. Quote
Fisher-O-men Posted July 22, 2014 Posted July 22, 2014 This is a good opportunity to get a tip that is maybe better than new, although Crucials are pretty good. Make sure the new tip will handle braid. Quote
Loop_Dad Posted July 22, 2014 Author Posted July 22, 2014 This is a good opportunity to get a tip that is maybe better than new, although Crucials are pretty good. Make sure the new tip will handle braid. I would do that except I don't know where to get them or don't know what is 'better'. There is one fishing store near by but they look like their main business is selling live baits and not much more. Quote
shanksmare Posted July 24, 2014 Posted July 24, 2014 Here is on place that may be of help to you that is in Austin, TX: http://www.papachopsrodandreelrepair.com/ I'm sure there are many more in the area. Quote
Loop_Dad Posted July 24, 2014 Author Posted July 24, 2014 Here is on place that may be of help to you that is in Austin, TX: http://www.papachopsrodandreelrepair.com/ I'm sure there are many more in the area. Wow, thanks shanksmare, I drive right by them like 50 yards from them every day to and from work. I believe this is operated in residential area. I'll stop by. Quote
Super User MickD Posted July 24, 2014 Super User Posted July 24, 2014 Finding a shop for this is probably harder than just doing it yourself. 1. Measure the diameter of the tip of the blank, as has been suggested. If you don't have calipers or micrometer, ask one of your "shoppy" friends; they will help. Convert to 64'ths of an inch. The tiptop you will order will be the next highest 64th conversion above what you measured. 2. Assume, like has been suggested, that the diameter of the ring is a 6 mm. It won't be far off, and this is the ring diameter that you will order. 3. Look at the tiptop that broke off. Is it a. silver or b. titanium (a little darker than silver) or c. black. One of these is the finish you want. 4. Call Jann's netcraft with this info and buy from them a tiptop with these specs. The ring material will be up to you; I would go with the hardest you want to afford, talk to Jann's about this. Also order some hot melt cement from them. 5. When you get the part in hand, heat the hot melt and smear it onto the blank and try to get slivers of it into the barrel of the tiptop. Heat the tiptop with a match only until the hot melt moves easily and slide the tiptop onto the blank, aligning it with the other guides. 6. Not rocket science, don't get intimidated, you can do it. Quote
Super User Munkin Posted July 25, 2014 Super User Posted July 25, 2014 Did the rod tip break off (blank break) or is the tip itself just broke? I have broke a few tips and yes you can measure with calibers, etc. or do it the easy way. Call Shimano and ask as they have good custp is easyomer service. I crushed a Gloomis tip and just called to ask the size and they sent me 3 free. Replacing a tip is very easy as long as you can operate a Bic lighter. Allen Quote
Loop_Dad Posted July 25, 2014 Author Posted July 25, 2014 Did the rod tip break off (blank break) or is the tip itself just broke? I have broke a few tips and yes you can measure with calibers, etc. or do it the easy way. Call Shimano and ask as they have good custp is easyomer service. I crushed a Gloomis tip and just called to ask the size and they sent me 3 free. Replacing a tip is very easy as long as you can operate a Bic lighter. Allen I didn't brake the blank, just the guide of the tip got crushed. Didn't though of just calling Shimano! Thanks, I will call them. Quote
Jaynoob Posted August 4, 2014 Posted August 4, 2014 The rod tip of my Crucial (6'8" MHF) got broken. I tried to buy replacement kits from eBay which didn't go well. I wasted too much time already. Now I'll just going to order correct one from jannsnetcraft to be done with. However I am not sure which one is the right one. How do you figure out the right tube size, ring size and type of the tip? They have lots of choices here: http://www.jannsnetcraft.com/fuji-tip-tops/ Honestly if it's a shimano crucial, I believe they have a lifetime over the counter warranty. If there's a bass pro shop or any big box store that sells shimano should swap it out no problem. Quote
Loop_Dad Posted August 4, 2014 Author Posted August 4, 2014 Honestly if it's a shimano crucial, I believe they have a lifetime over the counter warranty. If there's a bass pro shop or any big box store that sells shimano should swap it out no problem. I've already replace the tip, but I didn't think a tip damaged by user error was covered by warranty....or is it? Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.