fishman393

Stripers?

For some reason my remote should turn off after 30 sec. I just went to the boat to get ready for my tournament tonight and the remote is still on from a week ago. Took out the battery replaced it turned it back on and it still will not shut off. Any ideas?? They don't sell the battery's around my town and need my trolling motor to run all night

Well he got it welded for me. He only charged me 67 dollars to fix. He said he can't promise it will work.he welded both side he said Could last a day or could last a life time. Lol. He said he has done 3 of the same boat in the same spot and none came back so far.. Kinda scary well I got to put it all back together and give her a shot. Might think about saling but would hate to give someone else a problem.

The a good tool and cheap for what they do.

Thanks all. just a bit upset I just bought the boat from a guy and said no leaks I take it out and it leaks bad. Ripped the floor out cause the welder request so he can weld both sides of it. Of course I try calling the guy I got it from and low and behold no answer. So long story short I have replace every bit of wire ,live well ,switches and added my 999ci si hd. Lol the list goes on. Should be close to new internally when I'm done. Just hope the welds will hold up after he gets done with it. :/

What would cause this to happen?

I had a post about getting my boat welded well it's time for the guy to weld my alumacraft thay I just got and he said they are known for cracking at the factory welds and I may think about going with a different boat. Has anyone ever heard this about them? It's a 2003 175 invader and has 3 factory welds thay have cracked and causing the hull to crack

I hoping in the next two weeks for me still waiting for someone to have the time to weld it. Small town drama. The only two people in this town are booked up for the next 2-3 weeks so gives me time to mess with stuff. Until then I have my john boat until it sales. Got 1 guy looming at it tomorrow. Hope it sales but want to fish. Lol

I was ticked at the guy but. What can I say my fault I should of known when I could not take it to water to just wait. But for 4100. I could not pass. I had it on the water and don't see any other problems with it yet. It rode nice and the trolling motor with i pilot is amazing. Hoping this is all. The only other thing is wiring that I am working on and making the live well run the right way all and all I get to miss spawn time. Lol

Ok so I went and bought a boat 2003 alumacraft with 90hp no water close to test run boat.but k got to see the the motor run and start great.no problems. So I take it to the dmv get it in my name and all the legal stuff. Take it to the lake and low and behold it's taking on about 2 gallons a hour. Checked all drain plugs and live well no leaks. Take it home and fill it with water and watch I find a cheap weld patch and a crack in front of it.. geerr. So to my question in the picture I removed floor above cracks and removed foam. The crack is in the circled area. Did I remove enough for some one to weld the for me? I did it to save monet and want it welded top and bottom?

Yes thank you all I finally got the only boat place to talk to me. I ordered the 3way switch, pump, new hoses and a screen but forgot to get a screen for the in side for the drain/recurulating hole easy fix though. Thank you all for your help.

No pump.. the over flow is like 2 inch hose. The drain hose I like 1/2 to 1 inch. I'm thinking I found a picture finnaly. This might work for me. Thank you guys

The hose to the on with the PVC is just sitting in the boat no pump no where to connect it. That black disk next to the white PVC is the over flow I think. It's a 2 inch tube to the back where I wrote over flow.

There is only three hoses on the thing. Got a killer deal on this boat. I will try to get real pictures of it. Only 1 boat shop here and there to bust to look at it..