There was a good conversation last time I posted my crappie trip results and I promised that I would go into more detail on my next trip. Well, that trip was yesterday. Although they were not biting as well as the last time out (if you can consider 40 vs 80 fish a slow day) we were able to bring home some slabs for a friend who had never had crappie. That also meant I got to clean fish which was not what I wanted to do. This is my version of a crappie 101 and I'm sure others have setups they prefer.
Gear: I included pictures of my 2 main setups. Obviously, I only use spinning rods for crappie but you could throw the float setup on a baitcaster if you are so inclined. Both of my spinning rods/reels are Quantum Smoke. Rods are 6'8" MH. I have 6lb mono on the casting rig and 8lb mono on my float rig. I have one longer rod that is a JLM Elite that I use for dropping baits between boats and docks.
Presentation: There are 3 main ways I catch crappie. 1. Simple cast and retrieve on the rod with 6lb mono. Vary your retrieve depending where in the water column you want the bait to run. 2. Dropping and jigging the bait between boats and docks. Simply freespool the bait to the bottom (many times that's when you will get bit.) reel up about 2 turns of the reel and simply raise and drop your lure vertically. 3. Casting with a float. This is a great way to catch them and can be used from shore or a boat. I use the 8lb mono on this rig. Run your line through the float, tie on your jighead, put a small pinch weight about 3" up the line from the jighead (this helps the line feed through the float after you cast, acts as a stopper from reeling your jighead all the way to the float and gives better castability). Once you determine the depth you want your bait to be, I just tie a piece of fishing line above the float at that depth (you can use bobber stops). The line will reel up through the guides if I am fishing really deep but I like to keep my depth at around 6' if possible (that's why my rods are 6'8"). I cast the float setup out, let it settle, and then slowly lift my rod tip and pull the float, then let it drop. Pause for 30 seconds, then pull it again reeling up the slack and letting it sit. I do this all the way back to the boat. Most of the bites come as soon as the bait settles.
Terminal Tackle: Although you might see a small spoon or a roadrunner or a hair jig in my bait box picture, 99.9% of the time I am throwing the Gamakatsu jighead I pictured. I also have small pinch weights and of course floats. I like the line through floats since crappie are light biters and will spit a bait very quickly. The Jigheads I posted are a personal favorite and are super sharp but it's a challenge getting 8lb mono through double for a Palomar knot.
Scents: Most of the juices nibbles, etc., are a matter of personal preference. I us the 2 I pictured. I have found that the casting setup without the float normally doesn't need anything due to the moving action of the bait. I will say the Crappie Nibbles get stolen a lot and are sometimes frustrating trying to rig up. I use them to tip the jigs with either the tubes or curlytail jigs. I personally like the Smelly Jelly because it stays on the lure longer. I will admit, there are time either will increase bites.
So there you have it. My go to set ups for crappie fishing and we had a great day. Any questions, just ask. Best of all, everything I showed fits in a small tackle bag and is easy to carry and transport. 3 rods and I can fish for crappie most anywhere.
Sorry for the sideways pictures. This site flips and turns them and even if I go back in and edit them based on what shows on the site, they are never right.
.thumb.jpg.df52404fc648bc17a641a50eb4c9dac9.jpg)
