Jump to content

Recommended Posts

  • Super User
Posted

I only use locking wraps on Fuji KLH (very tall guides) or the first two Microwave single foot guides.  Not sure they are necessary, but tall guides are more likely to snag on stuff than more compact guides.  I don't use them on micros since they are so close to the blank that they never seem to snag anything.  I know that others prefer the locking wrap on all single foot guides.

 

For a locking wrap to have some utility it would have to prevent the guide from moving without the wrap epoxy being damaged.  Period.  I don't know if they do that or not.  The only guides I've seen that had damaged wrap epoxy were on old cheap big box store rods that probably didn't use enough epoxy when originally wrapped.  

Posted

On a guide with two opposing wraps like your double foot casting guide the guide has nowhere to go when stressed, all single foot guides with one wrap are not "locked down" and can be pulled from under the guide wrap. Epoxy finish has no real adhesive qualities nor any real strength, if that is important to you, use Perma Gloss.

The addition of extra guides to rods recently is the result of using limp braids and single foot guides in conjunction. Decreasing distances between the guides controls loops induced in the limp braided lines that can lasso a guide and pull it out. There is another way of doing it that decreases the size of the guides down to a point where braid is much more controlled in it's movement and can't induce loops that can grap a guide. A good analogy is, which is more accurate and controlled, a 22 caliber. bullet going down a bore of similar diameter, or one going down a 12 gauge bore? Now look at the amount of slop between your line and the guides on your rods, which analogy fits your situation? After all, why do you need such big guides when the line has already gone through a much smaller guide before it even reaches the rod on a casting design? The one on the reel.

  • Super User
Posted

I use dual locking wraps on every single foot guide. Easy to do, doesn't look bad, and gives me a little extra peace of mind. Why not, says me. 

  • Like 1
Posted

Running guides with short feet benefit especially from a locking wrap. Some guides with short necks and vertical supports make a neat locking wrap more difficult. It's really just preference and judgement. Like Gotti said "why not". As long as you can do a secure main wrap it's nothing worth losing sleep over though. 

  • Super User
Posted

Cannot argue with your logic, folks.  But I do disagree with the comment that epoxy has little adhesive properties.  Especially if CP is not used.

Posted

Epoxy has to help somewhat but it's no replacement for good wraps. I approach it with the thought that the thread secures the guide and the epoxy protects the thread. I avoid CP whenever possible. 

  • Super User
Posted
On 1/15/2017 at 3:03 PM, .ghoti. said:

I use dual locking wraps on every single foot guide. Easy to do, doesn't look bad, and gives me a little extra peace of mind. Why not, says me. 

Same, I use single footed "micro" guides about 98% of the time.  It's easy to do and effective, imo.

  • Super User
Posted
11 minutes ago, Delaware Valley Tackle said:

You just have to be careful with finish on the micros to not clog them. 

This is very true, lol.

  • Super User
Posted
2 hours ago, Delaware Valley Tackle said:

You just have to be careful with finish on the micros to not clog them. 

I wish I could say I don't know what you're talking about.

  • Super User
Posted
On ‎1‎/‎23‎/‎2017 at 10:44 PM, .ghoti. said:

I wish I could say I don't know what you're talking about.

 

Same here. My jig rod micros have some additional, um, "support" on them. Thankfully none got to the eye.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Unfortunately, your content contains terms that we do not allow. Please edit your content to remove the highlighted words below.
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.


  • Outboard Engine

    fishing forum

    fishing tackle

    fishing

    fishing

    fishing

    bass fish

    fish for bass



×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.